以下实验环境为`Redhat 7`。

注意：本文使用`ip`命令修改网卡（网络设备）名称，该修改是临时性的，如果出现异常，可以通过重启系统恢复配置。

# 查看网卡列表

```bash
[root@bogon ~]# ip link show
1: lo: <LOOPBACK,UP,LOWER_UP> mtu 65536 qdisc noqueue state UNKNOWN mode DEFAULT group default qlen 1000
    link/loopback 00:00:00:00:00:00 brd 00:00:00:00:00:00
2: enp0s3: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc pfifo_fast state UP mode DEFAULT group default qlen 1000
    link/ether 08:00:27:20:XX:XX brd ff:ff:ff:ff:ff:ff
3: enp0s8: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc pfifo_fast state UP mode DEFAULT group default qlen 1000
    link/ether 08:00:27:d2:XX:XX brd ff:ff:ff:ff:ff:ff
```

在修改网卡名称前，需要先停止网卡：

```bash
[root@bogon ~]# ip link set enp0s3 down
```

# 网卡名称：中文

```bash
[root@bogon ~]# ip link set enp0s3 name 我的网卡
[root@bogon ~]# ip link show
1: lo: <LOOPBACK,UP,LOWER_UP> mtu 65536 qdisc noqueue state UNKNOWN mode DEFAULT group default qlen 1000
    link/loopback 00:00:00:00:00:00 brd 00:00:00:00:00:00
2: 我的网卡: <BROADCAST,MULTICAST> mtu 1500 qdisc pfifo_fast state DOWN mode DEFAULT group default qlen 1000
    link/ether 08:00:27:20:XX:XX brd ff:ff:ff:ff:ff:ff
3: enp0s8: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc pfifo_fast state UP mode DEFAULT group default qlen 1000
    link/ether 08:00:27:d2:XX:XX brd ff:ff:ff:ff:ff:ff
```

结论：可以使用中文作为网卡名称。

# 网卡名称：英文单引号

```bash
[root@bogon ~]# ip link set 我的网卡 name "a'b"
[root@bogon ~]# ip link show
1: lo: <LOOPBACK,UP,LOWER_UP> mtu 65536 qdisc noqueue state UNKNOWN mode DEFAULT group default qlen 1000
    link/loopback 00:00:00:00:00:00 brd 00:00:00:00:00:00
2: a'b: <BROADCAST,MULTICAST> mtu 1500 qdisc pfifo_fast state DOWN mode DEFAULT group default qlen 1000
    link/ether 08:00:27:20:XX:XX brd ff:ff:ff:ff:ff:ff
3: enp0s8: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc pfifo_fast state UP mode DEFAULT group default qlen 1000
    link/ether 08:00:27:d2:XX:XX brd ff:ff:ff:ff:ff:ff
```

结论：可以使用英文单引号作为网卡名称。

# 网卡名称：英文分号

```bash
[root@bogon ~]# ip link set "a'b" name "a;b"
[root@bogon ~]# ip link show
1: lo: <LOOPBACK,UP,LOWER_UP> mtu 65536 qdisc noqueue state UNKNOWN mode DEFAULT group default qlen 1000
    link/loopback 00:00:00:00:00:00 brd 00:00:00:00:00:00
2: a;b: <BROADCAST,MULTICAST> mtu 1500 qdisc pfifo_fast state DOWN mode DEFAULT group default qlen 1000
    link/ether 08:00:27:20:XX:XX brd ff:ff:ff:ff:ff:ff
3: enp0s8: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc pfifo_fast state UP mode DEFAULT group default qlen 1000
    link/ether 08:00:27:d2:XX:XX brd ff:ff:ff:ff:ff:ff
```

结论：可以使用英文分号作为网卡名称。

# 网卡名称：英文冒号

```bash
[root@bogon ~]# ip link set "a;b" name "a:b"
[root@bogon ~]# ip link show
1: lo: <LOOPBACK,UP,LOWER_UP> mtu 65536 qdisc noqueue state UNKNOWN mode DEFAULT group default qlen 1000
    link/loopback 00:00:00:00:00:00 brd 00:00:00:00:00:00
2: a:b: <BROADCAST,MULTICAST> mtu 1500 qdisc pfifo_fast state DOWN mode DEFAULT group default qlen 1000
    link/ether 08:00:27:20:XX:XX brd ff:ff:ff:ff:ff:ff
3: enp0s8: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc pfifo_fast state UP mode DEFAULT group default qlen 1000
    link/ether 08:00:27:d2:XX:XX brd ff:ff:ff:ff:ff:ff
[root@bogon ~]# ip link set "a:b" name "enp0s3"
Cannot find device "a:b"
```

**结论：网卡名称可以包含英文冒号，但是这个名称无法被使用。**

玩坏了，重启系统。

# 网卡名称：反斜杠号

```bash
[root@bogon ~]# ip link set enp0s3 name "a\b"
[root@bogon ~]# ip link show
1: lo: <LOOPBACK,UP,LOWER_UP> mtu 65536 qdisc noqueue state UNKNOWN mode DEFAULT group default qlen 1000
    link/loopback 00:00:00:00:00:00 brd 00:00:00:00:00:00
2: a\b: <BROADCAST,MULTICAST> mtu 1500 qdisc pfifo_fast state DOWN mode DEFAULT group default qlen 1000
    link/ether 08:00:27:20:XX:XX brd ff:ff:ff:ff:ff:ff
3: enp0s8: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc pfifo_fast state UP mode DEFAULT group default qlen 1000
    link/ether 08:00:27:d2:XX:XX brd ff:ff:ff:ff:ff:ff
[root@bogon ~]# ip link set "a\b" name enp0s3
```

结论：网卡名称可以包含反斜杠号。

# 网卡名称：空格

```bash
[root@bogon ~]# ip link set virbr0 name "a b"
RTNETLINK answers: Invalid argument
```

结论：网卡名称不能包含空格。

# 网卡名称：斜杠号

```bash
[root@bogon ~]# ip link set "enp0s8" name "a/b"
RTNETLINK answers: Invalid argument
```

结论：网卡名称不能包含斜杠。